MFP 3000 C
- Description
- MEASUREMENT APPLICATION
- TECHNICAL PARAMETER
- VIDEO
- DOWNLOAD
Description
Version for testing filter media better than DIN 71460 and ISO 11155-1 road vehicle interior filters
Description
Version MFP 3000 C is especially tailored to the requirements of the DIN 71460 and ‘ISO 11155-1 Road vehicle interior filters’ measurement procedures.
Aerosol generation with RBG 1000 G (DIN 71460) and AGK 2000 (ISO TS11155-1):
The dosing air for the RBG 1000 G and AGK 2000 solid particle aerosol generators is regulated with a mass flow controller. This ensures the same operating conditions are always maintained.
DLB 2000 compressed air humidifier for the dispersion air:
Dry compressed air is normally used for aerosol generation, whereby, at the very low volume flows in filter media testing, the rel. humidity of the test volume flow can drop considerably. The DLB 2000 compressed air humidifier can condition the rel. humidity and temperature of the RBG 1000 dispersion air precisely to the required values and thus minimises the influence of rel. humidity on the dust holding capacity to be measured.
Aerosol inlet and aerosol neutralization on MFP 3000 C:
The aerosol inlet on the MFP 3000 C is equipped with a corona discharge to neutralize the test aerosol and ensures a homogeneous distribution of the test aerosol in the raw gas channel. The simple construction allows rapid replacement of the aerosol generator and the raw gas channel is easy to clean.
welas® 2100 aerosol sensors:
The welas® 2100 high concentration sensors ensure unambiguous and coincidence-free fractional separation efficiency measurement with very good count statistics at the specified concentration of 75 mg/m3 ‘ISO A2 Fine dust’. These sensors are also fitted with a special aerosol guide that minimises contamination of the internal optics.
Software:
Various differential pressure levels can be set in the filter media test sequence program for loading in accordance with DIN 71460. The clear definition of the test parameters in the pre-programmable sequence programs ensure very high level comparability of the results.
Benefits
- Virtually simultaneous particle measurement in the raw gas and clean gas
- Particle size measurements from 0.2 – 40 µm
- Measurement of Cn max= 105 particles/cm3 without dilution
- Internationally comparable measurement results
- Widespread distribution of the measurement system
- High reproducibility of the testing method
- Easy use of different test aerosols, e.g. SAE Fine and Coarse, NaCl/KCl, DEHS
- Highest raw gas concentrations of up to > 100 mg/m3 (ISO Fine) or > 500 mg/m3 (ISO Coarse) with measurement of the fraction separation efficiency for burden tests
- Flexible filter test software FTControl
- Sequence programs for pressure loss measurements, measurements of fraction separation efficiency and burden measurements
- Easy to operate, even untrained personnel can be instructed quickly in the use of the equipment
- Short set-up times
- Cleaning and calibration can be performed autonomously by the customer
- Easy use of the measurement technology components – even in other applications
- Mobile setup, easy to move on castors
- Reliable operation
- Validation of the clear function of individual components and the overall system during pre-delivery acceptance testing and upon delivery
- Low-maintenance
- The unit will reduce your operating costs
Applications
- Testing of filter media and small filter elements in product development and during production monitoring.
- Testing option based on ISO 16890 (General ventilation air filters), the test procedure according to ASHRAE 52.2 or EN 779 is optional available.
Measuring range (dimensions) 0.2 – 40 µmVolume flow 1 – 35 m3/h (suction mode)Dimensions 680•2,500•1,550mm (width•height•depth)Inflow velocity 5 – 100 cm/s (other sizes on request)Differential pressure measurement 0 – 5,000 PaMedia test area 100 cm²Aerosol Dust (e.g. SAE dust), salt (e.g. NaCl, KCl), liquid aerosol (e.g. DEHS)Aerosol Concentration Up to 1,000 mg/m3 for SAE fine dust without additional dilution (ISO A2 fine dust)Compressed air supply 6 – 8 bar
Coming Soon
Related products
-
Aging and Durability, All Brands, All Brands, All Brands, All Brands, All Brands, All Brands, All Brands, All Brands, military sonder, military sonder, pressure and bending, protective materials, safety, safety property of equipment, safety protection, textile and garment, WAZAU
DMS Compression Force Sensor
Read moreQuick View -
automotive interiors, Colour Management, Electronics, Electronics, Electronics, food, light industry shoe materials, light industry shoe materials, packing materials, packing materials, paper, plastics, shoe materials, textile, toys and children's products, X-Rite
X-Rite Ci4200 Compact Benchtop Spectrophotometer
Read moreQuick View